Determination of carbapenems in water samples by UHPLC–MS/MS

A rapid and reliable method for the detection of five carbapenems (biapenem, imipenem, doripenem, meropenem, and faropenem) in water was developed and validated. After acidification of water samples with acetic acid, carbapenems were isolated using a Bond Elut PPL cartridge. The target compounds were separated using ultra high performance liquid chromatography with a chromatographic run time of 5 min and detected on a triple quadrupole mass spectrometer operated in positive electrospray ionization and multiple reaction monitoring mode. Mean recoveries were in the range of 76.6–106.5%, with satisfactory intraday and interday relative standard deviations lower than 10.0 and 10.8%, respectively. The limits of detection and quantification were in the ranges of 0.05–0.2 µg/L and 0.1–0.5 µg/L, respectively, depending on the analyte. The proposed method was applied to the analysis of river samples and wastewater samples from swine farms, and no carbapenems were detected in the collected samples.     

Organophosphate esters by GC–MS: An optimized method for aquatic risk assessment

Organophosphate esters used as flame retardants and plasticizers are ubiquitous contaminants in surface waters. Many studies indicate that these compounds are neurotoxicants, endocrine disruptors, and may affect reproduction and development of aquatic organisms. Thus, analytical methods that allow accurate quantification of these contaminants at environmentally relevant concentrations are desirable for risk assessment studies. In this study, a method based on solid phase extraction and gas chromatography coupled to mass spectrometry was developed for determination of organophosphate esters in river water extracts. Multivariate optimization was used to determine the best conditions for injection of larger volumes of sample in a Programmable Temperature Vaporization inlet. Furthermore, the matrix effect on the instrumental response was evaluated and compensated by association of extraction‐blank‐matched calibration and isotopically labeled focus standards. The method quantification limits ranged from 0.009 to 0.11 µg/L, staying below the predicted non‐effect concentration for the aquatic compartment for all analytes, which is a requisite for using in risk assessment studies. The method was applied to freshwater samples collected in rivers from the Sao Paulo State, Brazil, and eight out of the ten target organophosphate esters were quantified, being tris(2‐chloroisopropyl) phosphate and tris(phenyl) phosphate the most frequently detected compounds.     

A new molecularly imprinted polymer for selective extraction and pre‐concentration of guaifenesin in different samples: Adsorption studies and kinetic modeling

This paper describes the synthesis of a molecularly imprinted polymer by chemical oxidation of pyrrole as the functional monomer, and at the presence of guaifenesin as the template. The prepared polymer was used as adsorbent in molecularly imprinted solid‐phase extraction followed by spectrophotometric determination. Different parameters in the solid‐phase extraction including sample pH, adsorbent weight, washing solution, and elution solvent were studied to determine optimum conditions for isolation and enrichment of guaifenesin. The results showed guaifenesin was quantitatively adsorbed on the molecularly imprinted polymer at pH 6.0 and completely eluted with an ethanol–water solution (50% v/v). An enrichment factor of four with satisfactory recoveries (87.0–95.0%) was obtained. The solid‐phase extraction columns could be used for up to six consecutive elution‐loading cycles without significant decreases in the analyte recoveries. The method had a dynamic range of 3.0 × 10^?6–1.5 × 10^?4 mol/L with a limit of detection and limit of quantification of 1.4×10^?6 and 4.5×10^?6 mol/L, respectively. The proposed procedure was used for the extraction and determination of guaifenesin in different pharmaceutical formulations, with satisfying results being achieved.     

Determination of personal care products in water using UHPLC–MS after solid phase extraction with mesoporous silica‐based MCM‐41 functionalized with cyanopropyl groups

A silica‐based MCM‐41 mesoporous material functionalized with cyanopropyl groups has been synthesized by cocondensation, characterized and applied to preconcentrate six parabens and three UV filters in river and swimming‐pool waters. The analytes were quantified by ultra‐high performance liquid chromatography‐tandem mass spectrometry, according to the Directive 96/23/EC. Even though matrix effect was negligible, quantification in river water samples with the standard addition approach improved the recoveries obtained using solvent‐based and even with matrix‐matched calibration. The method quantification limits in river water samples were 0.05 ng/mL for 2,4‐dihydroxybenzophenone and 0.01 ng/mL for the rest. Recoveries, evaluated for a concentration level of 0.5 ng/L, were in the range 93.5‐107.6% for parabens and in the range 64.2‐85.8% for UV filters, with relative standard deviations intraday ≤10.2 and 10.8%, respectively. This parameter, evaluated for a concentration level of 0.1 ng/L, ranged between 98.3 and 110.4% for parabens and between 61.9 and 89.9% for UV filters, with relative standard deviation intraday ≤15.3 and 15.5%, respectively. The two UV filters with lower recoveries were the most affected by the addition of sodium chloride. River and swimming pool waters were analyzed and all the personal care products were found in the swimming pool water, whereas only methylparaben was detected in the river water.     

Photo-driven water splitting photoelectrochemical cells by tandem organic dye sensitized solar cells with I−/I3− as redox mediator

Dye-sensitized photoelectrochemical tandem cells have shown the promise for light driven hydrogen production from water owing to the low cost,wide absorption spectra in the visible region and ease to process of their constitutive photoelectrode materials.However,most photo-driven water splitting photoelectrochemical cells driven by organic dye sensitized solar cells exhibit unsatisfactory hydrogen evolution rate,primarily attributed to their poor light capturing ability and low photocurrent performance.Here we present the construction of a tandem system consisting of an organic blue-colored S5 sensitizer-based dyesensitized photoelectrochemical cell(DSPEC) wired in series with three spectral-complemental dyes BTA-2,APP-3 and APP-1 sensitizers-based dye-sensitized solar cell(DSC),respectively.The two spectral-complemental chromophores were used in DSC and DSPEC to ensure that the full solar spectrum could be absorbed as much as possible.The results showed that the photocurrent of tandem device was closely related to the open-circuit voltage(Voc) of sensitized DSC,in which the tandem configuration consisting of S5 based DSPEC and BTA-2 based DSC gave the best photocurrent.On this basis,tandem device with the only light energy and no external applied electrical bias was further constructed of BTA-2 based 2-junction DSC and S5 based DSPEC and obtained a photocurrent of 500 μA cm-2 for hydrogen generation.Furthermore,I-/I3-was used as a redox couple between dye regeneration and O2 production on the surface of Pt-IrO2/WO3.The strategy opens up the application of pure organic dyes in DSC/DSPEC tandem device.     

Controlled Synthesis of Cr‐Co0.85Se Nanoarrays for Water Splitting at an Ultralow Cell Voltage of 1.43 V

Water splitting has attracted more and more attention as a promising strategy for the production of clean hydrogen fuel. In this work, a new synthesis strategy was proposed, and Co_0.85Se was synthesized on nickel foam as the main matrix. The doping of appropriate Cr amount into the target of Co_0.85Se and the Cr‐Co_0.85Se resulted in an excellent electrochemical performance. The doping of Cr introduces Cr³⁺ ions which substitute Co²⁺ and Co³⁺ ions in Co_0.85Se, so that the lattice parameters of the main matrix were changed. It is worth noting that the Cr0.15‐Co_0.85Se/NF material exhibits an excellent performance in the oxygen evolution reaction (OER) test. When the current density reaches 50 mA cm^?2 for OER, the overpotential is only 240 mV. For the hydrogen evolution reaction (HER) tests, the overpotential is only 117 mV to drive 10 mA cm^?2 of current density. Moreover, when the Cr0.15‐Co_0.85Se/NF material is used as a two‐electrode device for whole water splitting, the required cell voltage is only 1.43 V to reach a current density of 10 mA cm^?2, which is among the lowest values of the published catalysts up to now. In addition, the Cr0.15‐Co_0.85Se/NF catalyst also exhibits excellent stability during a long period of water splitting. The experimental result demonstrates that the change of the lattice structure has an obvious influence on the electrocatalytic activity of the material. When an external electric field is applied, it facilitates the rapid electron transfer rate and enhances the electrocatalytic performance and stability of the material.     

Fe/Co‐based Bimetallic MOF‐derived Co3Fe7@NCNTFs Bifunctional Electrocatalyst for High‐Efficiency Overall Water Splitting

Electrocatalytic water splitting to produce hydrogen and oxygen is regarded as one of the most promising methods to generate clean and sustainable energy for replacing fossil fuels. However, the design and development of an efficient bifunctional catalyst for simultaneous generation of hydrogen and oxygen remains extremely challenging yet is critical for the practical implementation of water electrolysis. Here, we report a facile method to fabricate novel N‐doped carbon nanotube frameworks (NCNTFs) by the pyrolysis of a bimetallic metal organic framework (MIL‐88‐Fe/Co). The resultant electrocatalyst, Co₃Fe₇@NCNTFs, exhibits excellent oxygen evolution reaction (OER) activity, achieving 10 mA/cm² at a low overpotential of just 264 mV in 1 M KOH solution, and 197 mV for the hydrogen evolution reaction. The high electrocatalytic activity arises from the synergistic effect between the chemistry of the Co₃Fe₇ and the NCNTs coupled to the novel framework structure. The remarkable electrocatalytic performance of our bifunctional electrocatalyst provides a promising pathway to high‐performance overall water splitting and electrochemical energy devices.     

Corrosion behavior of AZ91D magnesium alloy in distilled water

The corrosion of AZ91D magnesium alloy has received extensive attention due to the continuous expansion of its application field in recent years. However, the corrosion of AZ91D magnesium alloy in distilled water is relatively few. In this paper, the corrosion behavior of AZ91D magnesium alloy was studied in distilled water by electrochemical tests in combination with weight loss and surface analysis methods. The results indicated that the corrosion rate of AZ91D magnesium alloy increased with the increase of temperature and immersion time. The increase of the corrosion rate of AZ91D magnesium alloy with the increase of immersion time might be attributed to the damage of the structure of corrosion product film by hydrogen evolution, significantly accelerating the anodic process of AZ91D magnesium alloy. It was interesting that, in distilled water, the EIS of AZ91D magnesium alloy excluded an inductive arc in the low frequency region, which indicated that there was no the adsorption and desorption of aggressive ions or the damage and repair of film. The corrosion product film of AZ91D magnesium alloy in distilled water was composed of a compact inner corrosion product film and a loose outer corrosion product film.     

Two new NiII and ZnII metal–organic frameworks of glutarate and 1,4‐bis[(2‐methyl‐1H‐imidazol‐1‐yl)methyl]benzene ligands: syntheses,structures and luminescence sensing properties

Two new metal–organic frameworks (MOFs), namely, three‐dimensional poly[diaquabis{μ₂‐1,4‐bis[(2‐methyl‐1H‐imidazol‐1‐yl)methyl]benzene}bis(μ₂‐glutarato)dinickel(II)] monohydrate], {[Ni₂(C₅H₆O₄)₂(C₁₆H₁₈N₄)₂(H₂O)₂]·H₂O}_n or {[Ni₂(Glu)₂(1,4‐mbix)₂(H₂O)₂]·H₂O}_n, ( I ), and two‐dimensional poly[[{μ₂‐1,4‐bis[(2‐methyl‐1H‐imidazol‐1‐yl)methyl]benzene}(μ₂‐glutarato)zinc(II)] tetrahydrate], {[Zn(C₅H₆O₄)(C₁₆H₁₈N₄)]·4H₂O}_n or {[Zn(Glu)(1,4‐mbix)]·4H₂O}_n ( II ), have been synthesized hydrothermally using glutarate (Glu^2?) mixed with 1,4‐bis[(2‐methyl‐1H‐imidazol‐1‐yl)methyl]benzene (1,4‐mbix), and characterized by single‐crystal X‐ray diffraction, IR and UV–Vis spectroscopy, powder X‐ray diffraction, and thermogravimetric and photoluminescence analyses. Ni^II MOF ( I ) shows a 4‐connected 3D framework with point symbol 6⁶, but is not a typical dia network. Zn^II MOF ( II ) displays a two‐dimensional 4⁴‐ sql network with one‐dimensional water chains penetrating the grids along the c direction. The solid‐state photoluminescence analysis of ( II ) was performed at room temperature and the MOF exhibits highly selective sensing toward Fe³⁺ and Cr₂O₇^2? ions in aqueous solution.